亚洲熟女综合一区二区三区,免费夫妻生活片av,国产美女视频国产视视频,亚洲aⅴ男人的天堂在线观看

HomeHotlineContact
0position:Home>>News

Analysis of the reasons for the creeping and vibration of the edge milling machine

source:   author: time:2020-08-15 Visits:2459
There are many obvious abnormal phenomena in the milling machine, but in some economic CNC systems, there is no alarm. Even if there is an alarm sometimes, the alarm information shows that it is not the alarm of abnormal phenomenon you see. The creeping and vibration of the milling machine is an obvious example. When the milling machine runs at a low speed, the worktable of the CNC milling machine moves forward in a creeping manner; when the milling machine runs at a high speed, there will be vibration.

Because of the bad lubrication, the friction resistance increases when the milling machine table moves. When the motor is driven, the table does not move forward, which makes the ball screw produce elastic deformation and stores the energy of the motor on the deformation. When the motor continues to drive and the elastic force produced by the stored energy is greater than the static friction force, the milling machine table creeps forward and moves in this way again and again, resulting in crawling phenomenon.

Because the vibration frequency is proportional to the speed of the motor, the first thing to do is to check whether there is a fault in the motor, check the surface condition of the carbon brush and commutator, as well as the mechanical vibration, and check the lubrication of the ball bearing. The whole inspection does not need to be disassembled completely, but can be observed by the inspector. The bearing can listen to the sound with ears To check. If there is no problem, check the tachogenerator. The tachogenerator is usually DC.

A closed loop system may also cause system oscillation due to poor parameter setting. However, the best way to eliminate this oscillation is to reduce its magnification, to adjust RV1 and reverse clock direction in the FANUC system. At this time it can be seen that it will become better immediately. However, because of the relatively small range of RV1 regulating potentiometers, sometimes it can not be adjusted, it can only change the short circuited bar. Cut off the feedback resistance and reduce the magnification of the whole regulator.

More edge milling machines, with pressure beam milling machine, no pressure beam edge milling machine, end face milling machine, end face milling machine, planer. Please pay attention nchthg.com


All rights reserved:WUXISHI XILI MILLING MACHINE CO.,LTD(nchthg.com)  Su ICP 15043207-1 Design :25318.cn

国产av一区二区三区天堂综合网| 少妇愉情理伦片高潮日本| 欧美交换配乱吟粗大视频| 狠狠躁日日躁夜夜躁2022麻豆| avtt香蕉久久| 国产精品偷窥熟女精品视频| 国内揄拍国内精品少妇国语| 18禁超污无遮挡无码网址| 国产精品无码一区二区| 亚洲成A人片在线观看国产| 国产精品 无码专区| 伊人色综合久久天天五月婷| 国产亚洲人成在线播放| 国产成人啪精品视频免费网站| 国产精品久久久| 狠狠色噜噜狠狠狠狠色综合久 | 亚洲成av人片不卡无码 | 48沈阳熟女高潮嗷嗷叫| 中文字幕av一区二区三区人妻少妇| 人妻少妇边接电话边娇喘| 少妇人妻无码专区视频免费| 日韩国产成人精品视频| 熟妇高潮喷沈阳45熟妇高潮喷| 强壮公让我夜夜高潮| 好大好湿好硬顶到了好爽视频| 亚洲va久久久噜噜噜久久| 国产色综合久久无码有码| 我把护士日出了白浆| 久久精品中文字幕无码| 两个奶头被吃高潮视频| 国产A级理论片无码老男人| 亚洲国产婷婷综合在线精品| 欧美国产激情二区三区 | 久久久亚洲精华液精华液精华液| 亚洲av无码之国产精品| 亚洲色无码专区一区| 欧美日韩在线视频| 久久伊人色AV天堂九九| 无码精品视频一区二区三区| 欧美成免费a级毛片| 欧美日韩欧美|